What does fixed DPI mean? Simply put, it's the number of pixels. The higher the value set in an Laser Welding Machine, the better the print quality, but also the slower the print time. Common settings are around 300-600. Of course, setting it higher is fine. Laser Welding Machine manufacturers hope this will be helpful. Next, we'll set the relevant photo parameters for the YAG Laser Jewelry Welder. Most often, we'll set the flip and centering mode for the photo (there are also cases where flip is not selected. Under normal circumstances, flip is required). After setting, go to expansion, enable light processing, and adjust the saturation to control the print quality. The white area indicates no laser marking, and the black area indicates laser marking. Below is the progressive scan mode. Here, I usually use the line mode and set it to 0.5. Dual scanning is generally not recommended, as it's too slow for both scanning up and down. Adjusting the dot output is also unnecessary. On the right, set the speed to around 2000, the power to around 40 (the power setting depends on the product material, so the 40 setting here is for reference only. If you're using a phone case to print photos, the power can be set higher), and the frequency to around 30. The higher the frequency, the more concentrated the laser's output will be.

Most scientific piston pumps are double or triple-pump. When the piston moves backward, water is drawn into the sealed chamber through the inlet valve. When the piston continues to move forward, it forces water through the inlet and outlet valves to flow into the pump's inlet and outlet. Triple-pump pumps are a popular design choice for Laser Welding Machine applications because they produce a more stable flow. High-speed pumps can produce minimal pressure drop and have lower starting torque requirements. Double-piston pumps place higher and more stringent demands on system components and operators. YAG Laser Jewelry Welder can directly cause rapid failure, reduced suction volume, and sometimes produce excessive noise and potential damage. 90% of common problems with YAG Laser Jewelry Welder are not typically caused by the pump. Insufficient water flow capacity within the pump is the primary cause of premature failure. Common failures are caused by damaged materials or components (such as nozzle seals), or an inadequate inlet pipe that fails to allow sufficient water to enter the pump, leading to cavitation. Cavitation causes the gas environment mixed in the water to produce a small explosion, resulting in overpressure damage, and the surface quality of the piston material is seriously damaged.

1. The heart of an Laser Welding Machine is the high-pressure pump, which plays an irreplaceable role. A plunger pump is generally described as a piston that moves forward and backward. The piston is typically made of ceramic. Piston pumps are common, more efficient, longer-lasting, and less prone to damage. The plunger pump seal is mounted on the pump. Through a fixed seal and smooth cylinder walls, plunger pumps generally have good initial performance, but they cannot operate at excessive pressures and have a short lifespan. 2. The pump's capacity depends primarily on the pump speed. Unlike centrifugal pumps, which can increase or decrease flow, the pump must ensure the same amount of water enters and exits. Piston pumps have a very stable output parameter; the output flow remains constant regardless of pressure or injection time. For this reason, control systems are equipped with devices such as pressure relief valves. Blockage of the nozzle outlet can cause the high-pressure pump to withstand excessive pressure.

1. Glass fiber optics offer advantages in miniaturization and scalability due to their low manufacturing cost, sophisticated technology, and flexibility. 2. Unlike crystals, glass fiber optics do not require the same stringent phase matching requirements for outputting hydraulic piston light. This is due to the asymmetric broadening caused by Stark decomposition of the glass matrix, resulting in a wider absorption band. 3. Fiber optic materials have a very low volume-to-area ratio, resulting in fast heat dissipation, low losses, and a low laser threshold. 4. They can output a wide range of wavelengths, thanks to the rich energy levels and diverse types of rare earth cations. 5. They offer excellent tunability, thanks to the broad energy levels of rare earth cations and the wide fluorescence spectrum of glass fiber optics. 6. Because Laser Galvo Welder contain no optical glass in their resonators, they offer advantages such as no adjustment or maintenance, and high reliability, unmatched by traditional Laser Welding Machine. 7. Fiber optic cables allow the electric vehicle to be easily adapted for a variety of multi-dimensional, free-space processing applications, simplifying mechanical design. 8. It can withstand harsh operating environments, exhibiting high tolerance to dust, vibration, impact, humidity, and temperature. 9. No electric or water cooling is required, requiring only air cooling. 10. It boasts high photoelectric efficiency. Its comprehensive photoelectric efficiency exceeds 20%, significantly reducing power consumption during operation and lowering operating costs.

Laser Galvo Welder can achieve high-precision welding, with minimal heat damage and deformation, faster welding speeds, and smooth, aesthetically pleasing welds. No post-weld treatment is required, and the weld quality is high, with no vents. Precise control is possible, the focal spot is small, and the precision level is high, making automation easy. Depending on the solder material used in Laser Galvo Welder, there are four main types of solder available: solder bars, solder paste, solder rings, and solder balls. The key factor may be product characteristics. Most require three steps: spot heating, solder material heating, and molding heating. Therefore, the following parameters should be considered when choosing a solder material: 1. Select the solder material and welding method based on the product and production efficiency; 2. Select the power of the Laser Welding Machine; 3. Based on the actual effect and efficiency, determine whether visual effects and temperature feedback are required;

With the continuous development of Laser Welding Machine technology, its applications have expanded in recent years. Many customers are confused about the difference between laser welding and soldering wire. Which process is most suitable for their specific production site? Let's explore how to choose an Laser Welding Machine model. Laser soldering wire requires tinning materials such as tin bars, flux paste, tin rings, and tin balls, in contrast to traditional soldering with an electric iron. Laser soldering wire is non-contact and can be applied locally in confined spaces without any interference.

1. Press and hold the red mushroom button (emergency stop button) to disconnect the Laser Welding Machine's power supply. 2. After ensuring that no software is running on the industrial computer, exit the machine normally and enter standby mode. 3. Turn the key switch 90° to the "off" position to turn off the laser engraving machine's main power supply, and the indicator light will go off. 4. Remove the key and have a dedicated person store it for future use. 5. Securely close the lens cap. You probably know how to use an Laser Welding Machine. With the increasing emphasis on product branding, factories are now stamping their products with customer logos. This is why Laser Galvo Welder are used. They can print on various packaging and engrave exquisite designs, logos, and text. As a result, demand for them is growing. However, it is recommended to choose a reputable Laser Welding Machine manufacturer when purchasing.

1. Place a test piece (the workpiece being tested) of the same height as the Automatic Platform Laser Welder workpiece on the workbench or production line and ensure it is properly positioned. 2. Perform Automatic Platform Laser Welder testing using the Laser Welding Machine monitoring software. To optimize the testing results, perform the following adjustments: 1) Adjust the focal length by adjusting the head lift device. Adjust parameters such as power and speed in the Laser Welding Machine software. Enter the software, double-click the print date, and use the mouse to drag the print position to the appropriate location. 2) After completing the above steps, perform a test print. 3) Once the test is complete, repeat the test on the workpiece.

Many factories now use Laser Welding Machine, often featuring their own or their clients' logos on their products. However, many are new to Laser Welding Machine and have little understanding of their operation. As a result, many Automatic Platform Laser Welder manufacturers offer instruction, but some offer inadequate and unprofessional training, leading to inexperienced users. 1. Check the Automatic Platform Laser Welder's power plug to ensure it is properly connected and secure. 2. Insert the key switch and turn it 90° clockwise to the "On" position to connect the main power supply. The indicator light should illuminate. 3. Ensure the Automatic Platform Laser Welder's headlight button (emergency stop button) is pressed. 4. Turn on the computer monitor or desktop computer's main power switch. 5. Turn the red mushroom button in the direction of the arrow until it pops up. This will connect the Automatic Platform Laser Welder head to power. The Automatic Platform Laser Welder head should be operational after approximately one minute. 6. Remove the lens cap. The Automatic Platform Laser Welder is now powered on and can accept instructions from the operator for laser marking.

Laser Welding Machine can clean a wide range of materials and are widely used in a wide range of industries. They can be used to remove coatings from metal or glass surfaces, quickly remove paint, and not only completely remove them, but also gradually remove the surface paint film. Rapidly treat metal surfaces for rust prevention and various metal oxides. Remove grease, epoxy, glue, soot, dirt, and manufacturing sediment. Roughen metal surfaces. Rust prevention and degreasing of automotive parts before welding, as well as metal oxide and pigment stain removal after welding. Mold cleaning, such as tire molds, electronic molds, and food molds. Degreasing high-precision components after production. Deep cleaning of nuclear power plant components during maintenance. Oxide removal, paint removal, and rust prevention during the manufacturing or maintenance of aerospace weapons and ships. Cleaning metal surfaces in confined spaces.Cleaning precious cultural relics, rock formations, and building exteriors.? Now there are many objects that can be cleaned by Automatic Platform Laser Welder, including metal rust, metal particles, dust, etc., and the technology in this industry is more mature. It has been widely used in various industries and plays an important role in many fields, allowing people to use it with confidence.

Cleaning is essential for many industrial equipment, ensuring better maintenance. However, traditional cleaning methods often rely on chemical and mechanical cleaning, often leaving behind various chemical residues. This can damage equipment, leading to the search for better cleaning methods. Laser Welding Machine offer a promising solution. Their non-abrasive, contactless cleaning method not only provides excellent cleaning results but also protects the product being cleaned, earning them widespread recognition. When submicron-sized environmental contaminants adhere to the surface of a workpiece, they often cling too tightly to basic cleaning methods. Using nanotechnology, Automatic Platform Laser Welder radiation sources, to clean the surface of workpieces is highly effective. Because Laser Welding Machine perform contactless cleaning, they are highly safe and precise for high-precision workpieces or delicate areas. Laser rust removal offers unique advantages in this area.

1. Carefully read the Laser Welding Machine manual and strictly follow the safety procedures to ensure the safety of both equipment and personal safety. 2. During operation, pay attention to maintaining the environment and the cleanliness of the vehicle. Regularly check the laser rod and photoelectric device for contamination. 3. The Laser Welding Machine exterior must be safely grounded. During operation, avoid directing direct vision or contact with the laser beam (e.g., hands) to prevent injury. 4. If maintenance is required on the Laser Welding Machine, always turn off the power and ensure that the charge on the energy storage capacitors has been fully discharged before proceeding to prevent accidents. If any abnormalities occur during operation, turn off the power (press and hold the <Emergency Power Off> and air leakage switch) for inspection. 5. The cooling circulating water in Air-cooled Handheld Laser Welder must be kept clean, otherwise, it will affect the output size of the Laser Welding Machine. Customers can determine the cycle of replacing the cooling circulating water based on the starting time, water quality and other conditions. Generally speaking, the water change cycle in the fish tank is shorter in summer than in winter.

1. Is the Air-cooled Handheld Laser Welder output high (this is also crucial for efficiency and performance), is the energy stable (generally, the stable requirement is 2%, sometimes 1%), and is the performance ideal? 2. The Air-cooled Handheld Laser Welder light output must be of good quality, including both mode and reliability. 3. The Air-cooled Handheld Laser Welder must have marketable utility bills and be able to continue operating in harsh industrial production conditions. 4. The Air-cooled Handheld Laser Welder itself must have scalability, fault detection, and interlocking features, and a short shutdown time. 5. It must be user-friendly and have built-in function buttons to prevent operating errors and protect the vehicle from damage. 6. When testing an Air-cooled Handheld Laser Welder, ensure that the expected performance meets your requirements before purchasing. Currently, Laser Welding Machine have become a popular device in recent years. Many precision processes require ultraviolet light to meet these requirements. Furthermore, ultraviolet light is currently a popular intelligent laser engraving machine on the market. Although more expensive than other laser cutting equipment, the electronics industry cannot do without it. Air-cooled Handheld Laser Welder manufacturers believe that Laser Welding Machine have a small light spot and a small processing heat damage area, which is particularly suitable for ultra-fine laser marking and special material laser marking, as well as customers with higher requirements for laser marking effects.

1. Air-cooled Handheld Laser Welder manufacturers advise that people using pacemakers should not approach the equipment, as Laser Welding Machine generate electromagnetic fields during operation, which can affect the normal operation of the pacemaker. 2. Avoid looking at or touching the light (regardless of whether you are wearing safety glasses). Do not allow any part of the body, such as glasses, to come into contact with the laser or reflected light emitted by the equipment, as this may cause blindness or burns. 3. Keep the area around the equipment dry. When the equipment is not in operation, turn off the power and operate the equipment in one-handed mode if possible. 4. Do not insert any parts or objects into the laser engraving machine while the Air-cooled Handheld Laser Welder is operating normally. Do not use the marking system when the cover is open. 5. Do not place liquid containers on the chassis of the Air-cooled Handheld Laser Welder, and do not allow any water to come near it. 6. Do not accumulate flammable or explosive items or debris around the equipment. Do not place flammable items on roads with sufficient light or in areas where laser light is likely to irradiate. 7. Non-professional personnel are strictly prohibited from disassembling, repairing, or modifying the equipment. 8. Non-user personnel are prohibited from entering the marking work area. 9. Do not disturb power plugs and cables. If you detect any foul odor, immediately turn off the power and stop operation. 10. In the event of a fire or explosion, disconnect all power supplies and use a carbon dioxide gas or fire extinguisher to put out the fire.

In today's industrialized society, numerous and expensive equipment is used, and repairs can be very costly if problems arise. Thus, these devices require effective maintenance to extend their lifespan and reduce maintenance costs. Cleaning is essential during maintenance. However, traditional cleaning methods typically use chemicals, which can leave chemical residues on the equipment and cause damage. Air-cooled Handheld Laser Welder offer a simple and efficient cleaning method. Laser Welding Machine use a high-energy laser to illuminate the surface of the product, instantly volatilizing or removing rust or plating, resulting in a clean, environmentally friendly, energy-saving, and highly efficient industrial production tool. Specifically, they can be used for rapid paint removal, rust prevention, and the removal of metal oxides, oil stains, grease marks, and product residue. They can also be used for the restoration and storage of cultural relics.

Operate fiber-optic Air-cooled Handheld Laser Welder strictly in accordance with Laser Welding Machine operating procedures. After starting the Laser Welding Machine, manually start the CNC lathe in low gear (X and Y) and inspect for any abnormalities. Laser Welding Machine manufacturers recommend that operators do not leave their workstations or request assistance while the equipment is running. If leaving is absolutely necessary, shut down the machine or turn off the main power switch. During maintenance, follow high-voltage safety procedures. Perform maintenance every 40 hours of operation or weekly, and every 1,000 hours of operation or every six months, according to requirements and application procedures.

With the rapid development of society and the continuous advancement of technology across various industries, more and more equipment is emerging in industrial production. For example, Laser Welding Machine are becoming increasingly popular and can be used to mark various materials using laser beams. However, Laser Welding Machine also require certain procedures for proper operation. 1. Equipment should be operated and maintained by professionals. 2. Operators must complete training provided by the manufacturer's dedicated personnel before they can operate the equipment. 3. Water-cooled Handheld Laser Welder manufacturers remind operators to strictly follow the operating instructions to avoid damage to the equipment or even accidents caused by operating errors. 4. Before each shift, Water-cooled Handheld Laser Welder operators must thoroughly clean the equipment, lubricate and maintain all moving parts (such as slide rails and needle sleeves), and inspect the engine for loose screws. Ensure everything is intact before handing over or leaving the shift.

Generally, there is a device introduction on the back of the Laser Welding Machine body, from which you can get the power size of the device, other accessories information and safety maintenance knowledge. How to choose a device suitable for power? This depends on your requirements for the depth of the Water-cooled Handheld Laser Welder. For example, 30W can hit the depth, 20W is not enough, 20W can hit the depth, 30W device can produce the same effect by reducing the power to 20W, and actually adjust to the highest power when using it. You can use the credit card test method, buy several metal credit cards, adjust the power from 10, 15, 20, to the highest, and then drive the car on the credit card. Observe and touch it with your hands, and choose the one with the best effect, which is the best power. If you can't get the required depth even if you adjust it to the highest, then you can only buy a device with a higher power.

Nowadays, many OEM factories will use Laser Welding Machine. It is a very advanced laser equipment with a wide range of uses. It can mark on various products, and can have the characteristics of anti-counterfeiting, non-contact, high engraving precision, and fast marking speed and low cost. It can be controlled on the computer, but you must pay attention to the power of the equipment when buying Laser Welding Machine. The output power often mentioned in Laser Welding Machine is the same as the output power of household appliances commonly seen in our daily life. After all, Laser Welding Machine are also a kind of household appliances. The rated power indicates the size of the current mass per unit time. The greater the output power, the faster the power consumption. When used in Laser Welding Machine, it means that the greater the output power, the greater the kinetic energy that the Water-cooled Handheld Laser Welder can output, the heavier the marking depth, and the wider the adjustable laser marking depth.

1. Determine the materials to be processed, and place the sheet metal materials flat on the bed of the processing equipment. Then determine the stability of the material placement to prevent vibration during the Laser Welding Machine process, resulting in the Laser Welding Machine accuracy not meeting the requirements. 2. Operate the control panel, enter the product Laser Welding Machine pattern, and the thickness of the Laser Welding Machine material and other parameters, then adjust the Water-cooled Handheld Laser Welder to the appropriate origin position, and then self-reflect and adjust the vertical center of the nozzle. 3. Run the power supply and industrial chiller, set the temperature and pressure of the industrial chiller. 4. Run the laser generator, and then turn on the CNC lathe. However, in actual operation, it takes a lot of time to practice and understand every operation detail.

Laser Welding Machine are high-tech equipment and have become an indispensable processing equipment for modern industry. They can be effectively used for cutting non-metallic materials such as wood, plastic, acrylic, etc., not only with high speed. The accuracy is also very high, so many factories now have an increasing demand for Laser Welding Machine, but the operation of the equipment also requires professional training to be handy. The current Laser Welding Machine can make Water-cooled Handheld Laser Welder templates based on computers, and then directly enter the computer to automatically cut the graphics. The laser is of course light, but it is very different from ordinary light, because it only relies on spontaneous radiation in the initial short time, and the subsequent process is completely determined by the induced radiation source, so the laser has a very clear color. There is almost no specificity of emission, and a very high brightness unit. At the same time, the laser generator has high correlation, high toughness and high specificity. After the laser is generated, the laser is scattered by the reflector through the reflector and irradiated on the processed product, so that the processed product workpiece (surface) is subjected to strong heat and the temperature rises significantly. The points are melted or vaporized quickly due to the high temperature, and the laser cutting head is used to track them to achieve the purpose of production and processing.

1. Carbon steel Carbon steel is a very common metal composite material, widely used in various places in daily life. Laser Welding Machine can achieve welding, and the actual effect is better. The residue content determines the quality of spot welding. To ensure the quality of laser welding, heating is required when the carbon content exceeds 0.25%. When welding steels with different carbon contents, the gas welding gun can be slightly offset to the side of the low-carbon environmentally friendly material to ensure the quality of the joint. Because the heating and cooling rates during Water-cooled Handheld Laser Welder welding are very fast, when welding carbon steel, the sensitivity of welding cracks and vacancies will increase with the increase of carbon content. Steel with medium and high carbon steel content and ordinary carbon steel can achieve good laser welding, but heating and post-welding treatment processes are required to eliminate internal stress and prevent cracks. 2. Stainless steel plate Stainless steel welding is easier to obtain high-quality joints than basic welding. Laser welding machine manufacturers believe that due to the high welding efficiency and small heat damage zone of laser welding. It alleviates the adverse effects of overheating and large thermal expansion coefficient during stainless steel welding, and the welding has no defects such as pores and impurities. Compared with carbon steel, stainless steel is easier to have deep melting and narrow welding due to its low thermal conductivity, high laser energy absorption rate and high melting efficiency. Using small centrifug

When an Laser Welding Machine is working, if an emergency occurs (such as water seepage, abnormal sound from the laser generator, etc.), it is necessary to immediately turn on the direction and quickly disconnect the power supply. Be sure to turn on the external cooling water switch of the laser welding before operation. Because the laser generator system adopts the cooling water method. The laser generator adopts the air cooling method. If the cooling system is abnormal, it is forbidden to start the work. When the Water-cooled Handheld Laser Welder is working, its power circuit is in a high voltage and high current state. It is forbidden to touch the power circuit electronic components in the equipment during equipment operation. Untrained personnel are strictly prohibited from operating this equipment.

Laser Welding Machine are a new type of welding method. Because the welding speed of Laser Welding Machine is faster and more convenient to use, non-contact welding is adopted, and the operation is convenient and flexible, it has been well received by consumers. 1. Preparation before starting the Water-cooled Handheld Laser Welder Check whether the power supply and water circulation system of the Water-cooled Handheld Laser Welder are normal; whether the gas connection of the equipment in the equipment is normal; whether there is dust, oil stains, etc. on the surface. 2. Water-cooled Handheld Laser Welder start/standby Water-cooled Handheld Laser Welder start: connect the power supply, turn on the main power switch; turn on the chiller, laser generator, etc. in sequence; open the argon gas bottle valve, adjust the powerful gas flow; enter the operating parameters to be implemented at present; perform welding operations. Water-cooled Handheld Laser Welder standby: exit the program, turn off the laser generator; turn off the dust collector equipment, chiller and other equipment in sequence; turn off the argon gas bottle valve; turn off the main power switch.