With the rapid development of society and the continuous advancement of technology across various industries, more and more equipment is emerging in industrial production. For example, Laser Welding Machine are becoming increasingly popular and can be used to mark various materials using laser beams. However, Laser Welding Machine also require certain procedures for proper operation. 1. Equipment should be operated and maintained by professionals. 2. Operators must complete training provided by the manufacturer's dedicated personnel before they can operate the equipment. 3. Water-cooled Handheld Laser Welder manufacturers remind operators to strictly follow the operating instructions to avoid damage to the equipment or even accidents caused by operating errors. 4. Before each shift, Water-cooled Handheld Laser Welder operators must thoroughly clean the equipment, lubricate and maintain all moving parts (such as slide rails and needle sleeves), and inspect the engine for loose screws. Ensure everything is intact before handing over or leaving the shift.

Generally, there is a device introduction on the back of the Laser Welding Machine body, from which you can get the power size of the device, other accessories information and safety maintenance knowledge. How to choose a device suitable for power? This depends on your requirements for the depth of the Water-cooled Handheld Laser Welder. For example, 30W can hit the depth, 20W is not enough, 20W can hit the depth, 30W device can produce the same effect by reducing the power to 20W, and actually adjust to the highest power when using it. You can use the credit card test method, buy several metal credit cards, adjust the power from 10, 15, 20, to the highest, and then drive the car on the credit card. Observe and touch it with your hands, and choose the one with the best effect, which is the best power. If you can't get the required depth even if you adjust it to the highest, then you can only buy a device with a higher power.

Nowadays, many OEM factories will use Laser Welding Machine. It is a very advanced laser equipment with a wide range of uses. It can mark on various products, and can have the characteristics of anti-counterfeiting, non-contact, high engraving precision, and fast marking speed and low cost. It can be controlled on the computer, but you must pay attention to the power of the equipment when buying Laser Welding Machine. The output power often mentioned in Laser Welding Machine is the same as the output power of household appliances commonly seen in our daily life. After all, Laser Welding Machine are also a kind of household appliances. The rated power indicates the size of the current mass per unit time. The greater the output power, the faster the power consumption. When used in Laser Welding Machine, it means that the greater the output power, the greater the kinetic energy that the Water-cooled Handheld Laser Welder can output, the heavier the marking depth, and the wider the adjustable laser marking depth.

1. Determine the materials to be processed, and place the sheet metal materials flat on the bed of the processing equipment. Then determine the stability of the material placement to prevent vibration during the Laser Welding Machine process, resulting in the Laser Welding Machine accuracy not meeting the requirements. 2. Operate the control panel, enter the product Laser Welding Machine pattern, and the thickness of the Laser Welding Machine material and other parameters, then adjust the Water-cooled Handheld Laser Welder to the appropriate origin position, and then self-reflect and adjust the vertical center of the nozzle. 3. Run the power supply and industrial chiller, set the temperature and pressure of the industrial chiller. 4. Run the laser generator, and then turn on the CNC lathe. However, in actual operation, it takes a lot of time to practice and understand every operation detail.

Laser Welding Machine are high-tech equipment and have become an indispensable processing equipment for modern industry. They can be effectively used for cutting non-metallic materials such as wood, plastic, acrylic, etc., not only with high speed. The accuracy is also very high, so many factories now have an increasing demand for Laser Welding Machine, but the operation of the equipment also requires professional training to be handy. The current Laser Welding Machine can make Water-cooled Handheld Laser Welder templates based on computers, and then directly enter the computer to automatically cut the graphics. The laser is of course light, but it is very different from ordinary light, because it only relies on spontaneous radiation in the initial short time, and the subsequent process is completely determined by the induced radiation source, so the laser has a very clear color. There is almost no specificity of emission, and a very high brightness unit. At the same time, the laser generator has high correlation, high toughness and high specificity. After the laser is generated, the laser is scattered by the reflector through the reflector and irradiated on the processed product, so that the processed product workpiece (surface) is subjected to strong heat and the temperature rises significantly. The points are melted or vaporized quickly due to the high temperature, and the laser cutting head is used to track them to achieve the purpose of production and processing.

1. Carbon steel Carbon steel is a very common metal composite material, widely used in various places in daily life. Laser Welding Machine can achieve welding, and the actual effect is better. The residue content determines the quality of spot welding. To ensure the quality of laser welding, heating is required when the carbon content exceeds 0.25%. When welding steels with different carbon contents, the gas welding gun can be slightly offset to the side of the low-carbon environmentally friendly material to ensure the quality of the joint. Because the heating and cooling rates during Water-cooled Handheld Laser Welder welding are very fast, when welding carbon steel, the sensitivity of welding cracks and vacancies will increase with the increase of carbon content. Steel with medium and high carbon steel content and ordinary carbon steel can achieve good laser welding, but heating and post-welding treatment processes are required to eliminate internal stress and prevent cracks. 2. Stainless steel plate Stainless steel welding is easier to obtain high-quality joints than basic welding. Laser welding machine manufacturers believe that due to the high welding efficiency and small heat damage zone of laser welding. It alleviates the adverse effects of overheating and large thermal expansion coefficient during stainless steel welding, and the welding has no defects such as pores and impurities. Compared with carbon steel, stainless steel is easier to have deep melting and narrow welding due to its low thermal conductivity, high laser energy absorption rate and high melting efficiency. Using small centrifug

When an Laser Welding Machine is working, if an emergency occurs (such as water seepage, abnormal sound from the laser generator, etc.), it is necessary to immediately turn on the direction and quickly disconnect the power supply. Be sure to turn on the external cooling water switch of the laser welding before operation. Because the laser generator system adopts the cooling water method. The laser generator adopts the air cooling method. If the cooling system is abnormal, it is forbidden to start the work. When the Water-cooled Handheld Laser Welder is working, its power circuit is in a high voltage and high current state. It is forbidden to touch the power circuit electronic components in the equipment during equipment operation. Untrained personnel are strictly prohibited from operating this equipment.

Laser Welding Machine are a new type of welding method. Because the welding speed of Laser Welding Machine is faster and more convenient to use, non-contact welding is adopted, and the operation is convenient and flexible, it has been well received by consumers. 1. Preparation before starting the Water-cooled Handheld Laser Welder Check whether the power supply and water circulation system of the Water-cooled Handheld Laser Welder are normal; whether the gas connection of the equipment in the equipment is normal; whether there is dust, oil stains, etc. on the surface. 2. Water-cooled Handheld Laser Welder start/standby Water-cooled Handheld Laser Welder start: connect the power supply, turn on the main power switch; turn on the chiller, laser generator, etc. in sequence; open the argon gas bottle valve, adjust the powerful gas flow; enter the operating parameters to be implemented at present; perform welding operations. Water-cooled Handheld Laser Welder standby: exit the program, turn off the laser generator; turn off the dust collector equipment, chiller and other equipment in sequence; turn off the argon gas bottle valve; turn off the main power switch.

my country is a manufacturing powerhouse, so Air Cooling Handheld CW Laser Cleaner are often used in many industrial productions. As market demand increases, there are more Laser Cleaning Machine manufacturers on the market, but the prices range from tens of thousands to hundreds of thousands, and the quality levels are uneven. People have also become a problem in choosing. At present, the demand for laser welding equipment by Chinese manufacturers continues to increase. The reason is that laser technology is used for laser welding, which has faster welding speed, strong and beautiful welding, no need for secondary grinding and polishing, simple operation, and can realize automated mass production and processing, which further improves the efficiency of product production and processing and reduces labor costs for the company. First, it is necessary to clarify whether your own welding requirements and the welding functions of the manufacturer's equipment match, such as welding thickness, melting depth requirements, etc. Second, the quality of laser welding equipment must be considered. After all, tens of thousands of yuan for a piece of equipment is not a small amount. Before purchasing, it is best to go to the site to make a version and understand clearly whether the function requirements of the equipment are suitable. Third, the selection of equipment from well-known brand manufacturers and small brand manufacturers. Some customers think that the quality of laser welding equipment produced by well-known brand manufacturers must be better than that of small companies. I think there is no fixed standard. Customers buy equipment to create wealth and increase pro

The centrifugal fan is the main equipment of Laser Cleaning Machine. When the equipment is running for a long time, a lot of debris and dust will accumulate in the centrifugal fan. If the customer finds that the centrifugal fan makes noise when using the automatic cutting machine, it is necessary to clean and maintain it in time. After cleaning the centrifugal fan, the exhaust system of the centrifugal fan can be smoother and the noise problem can be avoided. There are also many lenses on Air Cooling Handheld CW Laser Cleaner. Workers should clean these lenses regularly, but they should use professional tools to operate during the cleaning process. To avoid scratching the lenses, follow the operating specifications when disassembling and installing the optical lenses. These are all maintenance knowledge that everyone needs to master. Finally, Air Cooling Handheld CW Laser Cleaner also need to choose a good manufacturer when purchasing, so as to ensure the quality, life and after-sales of the equipment.

Nowadays, the industry is developing faster and faster, and Laser Cleaning Machine are also used in various steel processing. They are widely used in the automotive manufacturing industry, the electronics industry, the medical field, jewelry design and other industries. It plays an important role in cutting, but Air Cooling Handheld CW Laser Cleaner equipment is relatively expensive. If you want to reduce the use cost and failure, daily maintenance is essential. Let's take a closer look. The cost of Laser Cleaning Machine is generally more than hundreds of thousands of yuan, so manufacturers will bear a heavier economic pressure when purchasing equipment. If you want to reduce the use cost of equipment, you need to pay attention to daily maintenance work, so that the equipment can maintain a good working condition and avoid increasing the use cost due to common failures and other problems. When using Laser Cleaning Machine, the water tank must be cleaned regularly, and cooling circulating water must be added inside when using the equipment. However, waste water cannot be used, because this water body has an important impact on the operation of the equipment, and the use of cooling circulating water will also directly affect the operation of the laser. Therefore, the water in the water tank should be replaced regularly, and the water tank should be thoroughly cleaned to avoid unremovable dirt in the water tank.

Traditional welding technology has not kept up with the development of the times, and in recent years, Laser Cleaning Machine have been gradually accepted by people and widely used in various industries. It is a high-tech equipment, handheld operation, flexible and convenient, can be welded indoors and outdoors, not only the effect is good, but also the cost is very low, but it has advantages and disadvantages. What are the advantages and disadvantages of Air Cooling Handheld CW Laser Cleaner? 1. Advantages The laser quality is good, the welding speed is faster, the welding is firm and beautiful, and it provides customers with welding solutions. High safety factor, the welding head is only effective when touching metal materials, and the touch switch has the magnetic induction function of human body temperature. Portable water-cooled gas welding gun, ergonomic design, easy to move, longer welding distance, can be used for welding of product workpieces at any position. High photoelectric conversion efficiency, low energy consumption, simple and easy to learn operation, no need for professional welding masters, ordinary employees can enter the job after a short training. Long-term use can greatly save production costs. Laser Cleaning Machine have the advantages of low heat damage, not easy to deform, blacken, leave no traces, deep welding, sufficient melting, strong and reliable. Air Cooling Handheld CW Laser Cleaner can be welded from any angle, and can weld various products with chaotic welding and large and medium-sized workpieces with irregular shapes. Complete welding at any focus. 2. Disadvantages Laser Cleani

1. High energy conversion level: The optical conversion efficiency of Laser Cleaning Machine is up to 30%, and the energy consumption is lower. 2. Convenient and flexible: Laser Cleaning Machine are easy and flexible, and can complete outdoor welding. 3. Welding does not require polishing: Continuous welding method, welding is beautiful and scar-free, and there are fewer subsequent polishing processes. 4. Wide application coverage: Applicable materials, the application scope covers almost most industrial fields. Widely used in kitchen cabinets, cabinets, staircase elevators, storage shelves, barbecue boxes, stainless steel anti-theft door guardrails, distribution cabinets, stainless steel furniture, field advertising, lighting and sheet metal chassis and other fields of complex and irregular welding processes. No one is perfect. Although Air Cooling Backpack Pulsed Laser Cleaner have many advantages, they also have certain defects. For example, people will feel sore in their arms after long-term handheld operation, and try to wear goggles during operation to avoid flying sparks during welding.

Traditional welding technology is poor, the joints are crude, and the functions are single. It has not kept up with the development of the times and has been gradually replaced by Laser Cleaning Machine. In addition, Laser Cleaning Machine are more convenient, feel good, and welding is easier and less tiring, so they are widely used in various places. The advantages of Laser Cleaning Machine are very long-lasting, and the operation is relatively simple, which can solve the problem of recruiting welders. Laser Cleaning Machine are a new record-breaking equipment. They replace the traditional fixed loop with a new generation of portable gas welding guns. They are flexible, convenient and fast, and can complete outdoor welding and long-distance welding. 1. Easy to use: Laser Cleaning Machine do not require professional welding knowledge. The operator only needs about an hour of training to start beautiful welding and solve the problem of recruiting welders. 2. High welding efficiency: The product welding speed is faster, 5-10 times that of the argon arc welding machine, and an average of 3 welding workers can be saved. 3. No consumables for welding: welding can be carried out without filling wire, and it is equipped with an automatic wire feeder. 4. The welding effect is very good: the Air Cooling Backpack Pulsed Laser Cleaner has a small damage area, no deformation, strong welding, and high aspect ratio.

Laser Cleaning Machine are considered to be a harmless cleaning method for statues. It uses the characteristics of laser light to increase the temperature of pollutants, causing pollutants to instantly fall off the surface of the statues. By controlling the parameters of the laser light, such as spot size and repetition frequency, the operator can accurately locate the laser energy required for cleaning, thereby removing pollutants without damaging the statues. Historical high-end statues such as stone carvings and stone carvings have become the first industries for Air Cooling Suitecase Pulsed Laser Cleaner technology due to their extremely delicate and fragile surface structure. We found that using lasers to remove stains on the surface of stone statues has its own unique advantages. It can very accurately control the movement of light on the intricate surface to remove stains without damaging the precious stone. With the help of laser, the maintenance personnel used laser light to remove the several millimeters thick gray-black scale covering the hand-carved patterns of the marble statue. The original color of the marble statue surface was reflected, making the delicate hand-carved patterns shine again. 1. Laser cleaning method, that is, using pulsed light to irradiate directly for decontamination; 2. Laser + boundary layer method, that is, first depositing a boundary layer on the surface of the substrate, and then using laser radiation for decontamination; 3. Laser + rare gas method, that is, while the laser is irradiating, a rare gas is blown to the surface of the substrate. When the waste is separated from the surf

The difficulty of Laser Cleaning Machine thick steel plate is much higher than that of metal sheet, and the appearance of the cross section is more obvious than that of the Air Cooling Backpack Pulsed Laser Cleaner texture of metal sheet. Therefore, the Laser Cleaning Machine cross section often encountered in the production and processing of hot-rolled strip steel, the quality of the finished product of the Air Cooling Backpack Pulsed Laser Cleaner is not only questioned. It will also continue to be accompanied by coarse grains and obvious sticky slag, so that the processing value of the Laser Cleaning Machine cannot be fully reflected. In the production and processing of the entire PCB circuit board of the metal sheet, sometimes the production and processing abnormalities of some areas will occur randomly. This will happen even when the processing machine is in good condition. Solving some processing problems will also affect the progress of the entire processing.

With the rapid development of society, people's demand for Laser Cleaning Machine is increasing, and various types of cutting equipment have appeared in the market. Among them, the more popular Laser Cleaning Machine are mainly used for thick plate processing, with fast cutting speed and high cutting accuracy. However, some problems will be encountered during the processing process. What problems will Laser Cleaning Machine encounter when processing thick plates? Let's take a closer look. Laser punching is the first process before Laser Cleaning Machine. The thicker the furniture board, the longer the punching time and the greater the proportion of the punching time. Therefore, in order to improve the efficiency of Laser Cleaning Machine, many laser manufacturers will make improvements in the punching time to ensure fast punching. However, in actual operation, there will be a situation of bursting holes, which is caused by the use of high-power automatic Laser Cleaning Machine and faster speed. On the contrary, the use of low-power single-pulse punching will cause the Air Cooling Suitecase Pulsed Laser Cleaner time to be too long, the output power to be reduced, and the product cost to increase.

The lower surface of the focusing lens in the condenser may also be contaminated by volatile organic compounds from the workpiece. When it is contaminated, it will also greatly affect the output of the Laser Cleaning Machine. Therefore, during production and processing, it is necessary to pay attention to the exhaust system and air blowing inspection and maintenance to minimize the contamination of the condenser. If the damage is serious, the following methods can be used for cleaning: (1) Remove the blowpipe, pressure ring and maintenance sleeve, and carefully remove the condenser; (2) Use a blower to blow away the dust on the surface of the condenser; (3) Use medical tweezers to carefully pinch the cotton ball and dip it in industrial ethanol or special lens cleaning fluid to gently wipe it. It should be gently wiped from the inside to the outside in one direction. After each wipe, the cotton ball needs to be replaced until the waste is removed. It must be noted that when wiping, you should wipe in the same direction, not back and forth, and not to be scratched by sharp objects, because the surface of the Air Cooling Suitecase Pulsed Laser Cleaner dual-light lens is coated with an anti-reflection film. If the film is damaged, it will seriously affect the power output of the Laser Cleaning Machine.

Nowadays, there is a great demand for steel plate processing in the industry, and its size is large and its weight is generally heavy. Laser Cleaning Machine will be chosen for processing. The cutting accuracy and effect will be guaranteed, but the long-term operation of Laser Cleaning Machine requires regular maintenance to ensure its safe and stable operation. Is it necessary to maintain Laser Air Cooling Suitecase Pulsed Laser Cleaner? Of course it is necessary. Let's talk about how to do regular maintenance in detail. The long-term use of reflective lenses will be polluted by the dust generated by production and processing, which will affect the output of the laser. Therefore, it is necessary to inspect and maintain it regularly to ensure cleaning. It can be cleaned with cotton wool dipped in industrial ethanol or special lens cleaner. It should be noted that even if cotton wool is not needed when wiping, other soft objects can be used instead, but products with sharp parts must not be used, otherwise it is easy to cause scratches on the mirror glass.

Laser Cleaning Machine use intuitive and simple control technology and customizable technical parameter libraries, so that novice welders can master cleaning and welding operations in just a few hours of training. Reduce labor costs while ensuring quality, consistency and productivity. Air Cooling Suitecase Pulsed Laser Cleaner are a product innovation that is easy to use, economical and intelligent. For different applications, the corresponding nozzles can be replaced more conveniently and quickly, making complex production simpler and more efficient. Compared with traditional welding methods, Air Cooling Suitecase Pulsed Laser Cleaner are more popular, with a handheld design, comfortable to hold, and a variety of functions. It has two modes, cleaning and welding, so people can choose, and it uses high-tech technology to meet your fine processing needs. There are also monitors to protect the lens and conduct damage warnings, so it is very popular in the market and has very good sales, so people can buy it with confidence.

In today's society, science and technology are developing more and more rapidly, and welding machines are gradually being replaced by Laser Cleaning Machine. In industry, it also has better cleaning effects, and when cleaning various equipment, it has the characteristics of fast speed, no damage to the substrate, and no pollutant emissions. Therefore, it helps to ensure the quality of welding. It can be seen that the use of Laser Cleaning Machine has many advantages, which makes the majority of customers and friends satisfied. Laser Cleaning Machine have two modes: cleaning and welding, which can be switched flexibly. The system is easy to use and can display I/OIO status, alarm information and movement status in real time. It is suitable for various pendulum types, automatic wire feeding and other functions. The process parameter library is stored in the Water Cooling Handheld CW Laser Cleaner automatic welding machine. Each mode corresponds to different basic parameters. After saving, the corresponding mode can be selected at the same time next time without resetting the parameters. In the actual welding operation, the appearance of hot-dip galvanizing, rust and oil stains will increase the difficulty of welding, increase the formation of pores, and thus affect the actual welding effect. Therefore, cleaning treatment must be carried out before welding metal materials. The traditional method is to use chemical water treatment or mechanical cleaning, which is time-consuming and labor-intensive, and produces waste.

Traditional Laser Cleaning Machine are bulky, slow in construction efficiency, and poor in effect. Therefore, the emergence of Laser Cleaning Machine is gradually replacing traditional welding equipment. It is exquisite and compact, with a compact and more reasonable internal structure. It can be moved by one person, easy to operate, with better effect, and lower welding cost. It is more in line with modern work needs, and has less harm to the human body than traditional welding methods. The efficiency of Laser Cleaning Machine is about 3-5 times that of traditional electric welding. The gas welding gun feels more ergonomic. It takes only a few minutes to learn and train to weld well. Professional welders are not needed. Refined management reduces the company's labor costs and improves productivity. The product has a service life of up to 100,000 hours and is very convenient to carry. Laser Cleaning Machine are a substitute for the argon arc welding machine and arc welding that we used to use. 1. Welding effect: Laser Cleaning Machine are not prone to blackening, deformation, or welding penetration. Because the power can be controlled by computer programs, Shandong Haohan can provide 500w-3000w power welding machines to achieve the welding thickness of various materials. 2. Productivity: The advantages of Laser Cleaning Machine over traditional welding methods are faster, more efficient, and lower product costs; easy to use, no professional welders are required, operators can also operate, reducing labor costs; welding is smooth and beautiful, no need for too much polishing, saving consumables, 3. New Water Cooling Handheld CW Laser

When buying Laser Cleaning Machine, you must buy them directly from the manufacturer, because many well-known brands on the market now have agents, and the product knowledge and technology that agents can master are relatively limited. In the later use process, if you encounter problems, it is difficult to get valuable technical training from the dealer. 1. You often have to find a manufacturer to buy, mainly because finding a manufacturer to buy can make people feel more at ease. 2. Before finding a manufacturer to buy, some manufacturers can apply for free version making, and the manufacturer will also select an Water Cooling Handheld CW Laser Cleaner suitable for product use according to the user's actual situation, and the quality of the product can be guaranteed to a certain extent. 3. Generally, when we are looking for manufacturers to order, we are more worried about the quality of the product. If the quality cannot be guaranteed to a certain extent, it will make people feel unacceptable, and they may worry about problems in the use process. If you find a manufacturer to buy directly, you don’t have to worry about the quality, because the manufacturer can guarantee the quality of the product. Nowadays, almost all products have a certain warranty period, and the manufacturer will also go to professional technicians for after-sales service, which can be seen by yourself. 4. Some manufacturers will also carry out customized production according to the user's special situation to meet the customer's requirements and meet the user's standards. 5. After the user orders an Water Cooling Handheld CW Laser Cleaner, the manufacture

1. In the basic parameters of the Laser Cleaning Machine, check whether the type of laser is appropriate. This is also the main reason for the failure of continuous lighting. 2. Drive the nine-core control line of the Laser Cleaning Machine, check and observe whether the control line is loose and whether the connection is unreliable. 3. Remove the control line on the Laser Cleaning Machine power supply, that is, the nine copper wires. Then, according to the transmission key of the laser power supply, we can distinguish whether it is a power supply failure or a motherboard failure. 4. If the aiming is normal, it means that the Laser Cleaning Machine power supply is normal and there is no problem. 5. If the photo is abnormal, it means that there is something wrong with the power supply. 6. When the power supply is normal, you can connect the control line, and then use a multimeter to measure the power switch on the junction box to control the pin. If the Laser Cleaning Machine does not light up and the normal working voltage is higher than 4V, if it is less than 3V, the motherboard output is abnormal. When it lights up, the working voltage should be less than 2 volts. If it is higher than 2.5 volts, the output is abnormal. 7. Check whether the water circulation system of the Water Cooling Handheld CW Laser Cleaner is abnormal, whether the water output is sometimes abnormal, and whether the water protection device is OK. If the Water Cooling Handheld CW Laser Cleaner does not emit laser, it can usually be checked through the above situations. If the above methods cannot solve the problem, the only option